Video Reviews
GOLDEN SOUND REVIEW – PUNCHING UP!
„I check out the, recently launched, Holo Audio Spring 3 DAC. Does it live up to the hype of being one of the finest sounding DACs for under £2,500?“
„Holy Trinity Of a DAC – Welcome to the flagship end of the Spectrum of a sublime DAC“
DAC Shootout! Holo May VS Spring 2 VS Spring 3!
You Need This Awesome DAC! Holo Audio Spring 3 KTE Review
- A new generation of linear compensation technology. A better solution to the resistance, accuracy errors caused by switching components and PCB, after compensations makes the equivalent accuracy reach 0.00005%.
- The new generation of de-glitch technology can provide a full range without increasing the noise floor or other adverse effects.
- Based on this new generation of technology, “泉3” Spring3 (non preamp model) can provide a SINAD of >112dB and a dynamic range of >128dB, which represents the performance limit reached by today’s most advanced R2R architecture DAC.
- Using the ultimate performance of PLL+FIFO technology, provides 0.1Hz Third-Order low-pass ability to inhibit jitter. It also uses a high-performance femtosecond VCXO as the PLL clock source. Under the premise of being almost immune to the front-end jitter, it can also lock up to 1.5us-2us @ 1KHz signal with high jitter. (It can lock up to 1.5us-2us @ 1kHz signal with high jitter on the premise of almost being immune front-end jitter).
- The USB interface uses proprietary firmware with ultra-low latency, a highly reliable data transmission, ideal USB eye pattern measurements that contributes to 2-4 times higher performance than official firmware.
- A single, independent HDMI-I2S input interface is provided, which has a four-way independent circuit, as opposed to standard LVDS chip, making I2S clock signals subject to lower interference and lower jitter. In addition, the I2S input can be configured with a specific pinout configuration, making it compatible with most of the HDMI-I2S digital devices on the market.
- Optional (Factory installed only): A fully balanced, fully discrete analog pre-amplifier. Provides 84 steps, each step is 1db of volume control.
Spring Models
Three versions of the Spring 2 DAC. Below are the three levels, and KTE being our no compromise model with all options:
(The base model is quite good all by itself and priced so competitively it’s impossible to beat the performance/price ratio.) This model has basic caps for the PSU, and does not include a CNC remote. It has standard Red label 5N Copper Otype Transformer, round wire type copper wiring. Considered the base model however packs a mean punch for price per dollar performance ratio. (no remote control in this version)
(With HoloAudio caps for ultimate power filtration and improved sound quality – Sound quality is refined and more relaxed, transparent and details are more refined and clear while remaining neutral. ) It has standard Red label 5N Copper Otype Transformer, round wire type copper wiring. This is a popular option for those who want a little more out of their dac with improvement of sound from the caps as well as this version will include the cnc machined aluminum remote control.
SPRING GEN 3 KTE (Kitsuné Edition)
The highest grade components are used in our very popular KTE version products. This Spring3 KTE version will include an upgraded ultra premium transformer that is 100VA O-Type flat wire type .The sound improvement is not subtle, it’s a night and day improvement in our opinion and many of our customers agree. Kitsune has tuned this Spring 3 DAC for no compromise performance and targeted at the enthusiast audio lover. This transformer is our finest available model and makes the Spring’s sound quite elegant and improved detail. more features mentioned below.
”OPTIONAL upgrade – Preamp Module” – Fully discrete and balanced relay controlled volume control. Controls all the digital inputs volume with precision. This has trickle down technology from our popular flagship Preamp the Serene. Using 4 amp modules and hundreds of transistors.
Digital inputs |
|
COAXIAL1, COAXIAL2, OPTICAL, AES | PCM 44.1-192K (24bit) DSD 64X (DOP) |
USB | PCM 44.1K-1.536M (32bit) DSD 64-512X DOP) DSD 64-1024X (Native) |
I2S | PCM 44.1K-1.536M (32bit) DSD 64-1024X |
Analog Outputs |
|
Single Ended (RCA) | DAC Voltage Output 2.9Vrms (Optional) Pre-amplifier Voltage Output 5.8Vrms |
Balanced (XLR) | DAC Voltage Output 5.8Vrms (Optional) Pre-amplifier Voltage Output 11.6Vrms |
Digital Specifictions |
|
PCM 48K NOS | THD+N 0.00032% @1K(-110dB) DNR 127dB |
DSD 128X | THD+N 0.00025% @1K(-112dB) DNR 115dB |
Physical Characteristics |
|
Size (Chassis) | 430x300x55mm (W x L x H, Dimensions do not include protruding parts) |
Weight | 8.5kg |
Power Specifications | 110-120VAC / 220-240VAC 50/60Hz |
DSD is natively supported for the first time on this Discrete Resistor Ladder DAC
HoloAudio is the world’s first to support DSD natively on Resistor Ladder DAC, so far the only one. This is not the DSD converted to PCM before digital-analog converter, but directly by the discrete components of the DSD digital to analog converter. Supported currently on MAC (DOP)and Linux (DOP), and Windows/PC (Direct Native and DOP). Please note, the word ‘R2R’ is the name of a kind of architecture of resistor ladders. This architecture requires less resistors yet still is capable to deliver more than acceptable performance. Most DACs in the industry use this architecture. The DSD module of Spring3 does not use R2R architecture for the DSD, more specifically it uses a very specific architecture which is optimized to perform DSD to analog. So to be entirely accurate the DSD part of Spring is using resistor ladders, not R2R..
Spring3 DAC R2R structure and design + Input/output Stage
Modern and popular delta-sigma type DAC differs from R2R within one clock analog value can recover a sampling point, and the delta-sigma is used to represent an analog signal after passing through oversampling and high-speed digital switching 0 and 1. In comparison, the conversion structure of R2R is most direct and pure, but delta-sigma is essentially a digital chip, high-speed digital signals 0 and 1 switch to the low-pass filter to process the analog signal and this process is prone to various problems, produce digital sound (digititus) and also in the super-sampling process will inevitably cause some ringing and distortion. But DAC R2R structure requires high-precision resistor network which the cost can be very expensive. And the digital delta-sigma DAC chip in comparison is very low cost. Patented R2R technology. This is the first discrete DAC that has Linear compensation and this allows for ultimate music reproduction accuracy. Dual R2R ladder network with advanced architecture for PCM, and Dual Resistor Ladder network with optimized architecture for DSD!
I/O stages: There is an Op Amp used for input stage and discrete component used for the output stage. The discrete output stage is working in pure class A. The output voltage is 2.9 Vrms for single ended output and 5.8 Vrms for balanced output (dsd playback is half these voltages). The single ended is RCA. Balanced is XLR. They both use the same output stage. It’s BiPolar Junction Transistors, direct coupled. The big MKP capacitor you can see in the output stage is for the power supply, not for signal coupling. And the output impedance is 200 Ohm.
A common question we get…” Why do you use an Op amp at the input of the DAC?”
The input stage with an opamp is a good choice. It has a paired transistor input by the nature it is manufactured. But an opamp for the output stage is limited due to it’s size and the thermal capability. Also, no one will offer an opamp with class A output as it’s efficiency is so low. So an opamp used as input and discrete output combined together will have an advantage. It doesn’t mean that all discrete is not good. Actually, if we need to achieve enough low distortion. It needs at least 30-40 transistors. Which not only will it be huge and waste of space but it will also be too costly. I mean, to beat the opamp’s performance, a simple discrete architecture is not possible, although an all discrete design looks beautiful.
The true balanced circuit design
These two pictures can explain the true balanced design quite well. The bottom side has the same resistor ladders as top side. The dac module is a pure 24bit discrete R2R design (PCM) and discrete Ladder Dac optimized architecture (DSD).
What are the Spring 3’s sound characteristics?
One of the strong points of the spring is the spatial sounds stage presentation. It’s very wide and precise. It never sounds congested like many DACs. The high end is very detailed and never harsh sounding. It has the R2R goodness that many have come to know and love. R2R has almost a cult like following and this DAC will surely become a sought after DAC. Everything comes effortlessly for this DAC. Bass is layered and textures, quite full and present without ever masking over the sweet mid tones that are produced. One special thing about the Spring is its amazing voltage regulation circuitry that better than 0.2uV output noise! This along with the O-core transformer helps regulate the purest power which translates to audio clarity and accurate reproduction. It must be heard to appreciate and come to love its sound.
Jeff Zhu comment on the Spring3
Spring3 PLL is nearly the same design as our flagship dac, the May. The main difference between Spring3 and May is that May uses our latest technology and cost is no object, therefore has better components. For Spring3, it uses the latest technology as May. But the main goal is to get high performance at reasonable cost, and I believe we absolutely achieved this goal. Although it’s price is higher than Spring2. I think the performance/cost ratio is higher than Spring2. It’s not much behind May! The pre-amp module inside is a very decent way to control volume, really one of the best ways. I think the digital volume is terrible, especially for this level of DAC. So I never added digital volume control on Spring and May, only on Cyan which is our entry level product. Digital volume is very easy and has very low cost added, albeit compromised. The reason we don’t use it is that ‘free digital volume’ will lead customer to use it and not realize it is not ideal for use with our higher end dacs. I don’t want misguide the user to use our DAC is that way. I think they will be most pleased with our fully balanced, discrete analog volume control for a low optional upgrade price.
Jeff Zhu – HoloAudio Explains his patented R2R technology
There are ways to improve the performance, the segment+R2R is one way. Trimming is another way. There is an additional R2R ladder in Spring, it compensate the main R2R ladder. It works like trimming, but trimming is to change the resistor value. This additional R2R ladder are digital controlled and is to compensate the resistor tolerance. For example, the MSB of 16 bits should have the value of 32768, but due to tolerance, it represent 32700 in real world. Then that additional R2R ladder will compensate 68 into it. Then it became 32700+68=32768.
Actually there are other ways to improve performance, I just told you two stories. There are more stories behind the design. It is really hard. I must count every via holes in layout, every PCB wire has it’s impedance and must put attention on it. A via hole can be 50 m Ohm, it is 1/20000 of 1 kilo-ohm, and you see, it covers 32768 which is the MSB of 16bits. Also the switches has self-impedance which is about several ohms to 30 ohms. If you find this issue. Maybe you will go crazy, it seems to be an impossible mission. But a good designer will overcome all these problems. It’s our value at HOLO Audio.
All the resistor tolerance, switch impedance, line impedance, via hole impedance, finally reflect as linearity. There is a chart that shows Spring’s linearity, it’s excellent. But I suggest you to look at THD performance. Bad linearity must result a bad THD performance. But good linearity doesn’t mean there will be good THD performance. THD is dynamic performance, more critical than linearity which is a static performance.
If you look at the THD performance, you will find Spring to maybe the best among those competitors. I’m applying a patent which contribute a lot of that performance. But I can’t tell you how. It’s confidential now.
R2R LINEAR COMPENSATION
There’s an additional R2R ladder in the Spring DAC, it compensates the main R2R ladder. It works like trimming, but trimming is to change the resistor value. This additional R2R ladder is digitally controlled and will accurately compensate the resistor tolerance. For example, the MSB of 16 bits should have the value of 32768, but due to tolerance, it represents 32700 in real world results. Then that additional R2R ladder will compensate 68 into it. Thus it now becomes 32700 + 68 = 32768. What this means is that it’s likely the most precise Discrete DAC on the market with near flawless linearity, lowest THD and highest SNR of any NOS DAC. The sound is simply something you must experience to fully realize how special this DAC is. It’s a patented technology exclusive to Holo Audio.
Marek (Verifizierter Besitzer) –
Today we compared this DAC with the Weiss 204 (which has a dedicated DYI power supply) and the Meitner Audio MA-3 and the results Spring Level 2 is a great DAC perfectly balanced between stage width, holography, beautiful natural vocals and holy impressive dynamics!
Andrew (Verifizierter Besitzer) –
I would like to thank you for the great correspondence and help in the purchase of the Spring 3 DAC Level 2, which I’m delighted with. Even straight out of the box the SQ improvement’s over the Naim nDac were substantial, not surprising as its over 10 years old. My RME ADI FS 2 DAC, which is very good, was shown a fresh pair of heels by the Spring DAC 3, sound stage is larger, imaging is holographic, bass is taught and deep and the way it reproduces instruments is amazing.
I know all DAC’s can reproduce sound accurately, but all of them sound different, Naim has the PRAT, which is why people buy their equipment, I’m one, RME sounded superb, compared to Naim, the Spring DAC walked over both with alarming ease, simply stunning.
Jaroslaw (Verifizierter Besitzer) –
I had limited time to listen to my new DAC even though I can tell that this is marvel! I wouldn’t think that it can improve all aspects of how the overall system sounds, but yet it does! Amazing, really.
The temperature of the device in the top right side of the chassis the temperature is a bit high, maybe 50 C. This is not a problem according to Magna Hifi
Hillebrand (Verifizierter Besitzer) –
After some good advice of Rob and a great listening session at Magna’s I purchased the Spring 3-2 DAC as a replacement for my Naim ND5XS. The Naim is still in place as a streaming device and digitally connected to the Spring 3. No regrets at all. The DAC is a great step forward in my listening experience. The DAC really invites you to listen to more and more music.
Bas de Vos (Verifizierter Besitzer) –
After another good and objective advice from the Magna team bought the spring3-2. And after some serious burn in time with quality ups and downs …. I can’t say anything else than it is stunningly amazing. Never experienced such live feeling at home. Staging, clarity is just amazing. Really happy. Give it some weeks of burn in and you will be amazed by the musical performance this machine can put in place.
Stephen Iannetta (Verifizierter Besitzer) –
Never has purchasing this amount of audible joy been so easy! Thank you for a gloriously easy transaction Magna!
I am utterly smitten with this product!
Wesley (Verifizierter Besitzer) –
Great service, awesome conversations, incredible knowledge, amazing sound and Rob is a superb host that takes his time for you. Bought a spring 3 lvl 2 dac and i love it.
Marcus (Verifizierter Besitzer) –
The first impressions are very positive . Very open, smoother, warmer and wider soundstage. compared to my Hegel.
Jule –
Sounds superb and made a huge improvement!
Carlos (Verifizierter Besitzer) –
I’ve owned the DAC for a few months now. This DAC is built so impressively and sounds amazingly clean. The tonal balance is beautiful and gives a very rich but not overly thick sound, which often causes listening fatigue, such as with my Pontus (which was sold after comparison with this Holo Spring ;-)
Max (Verifizierter Besitzer) –
I wanted to thank you for a pleasant and positive experience. I’ve been enjoying the DAC every day for weeks now. It sounds so beautifully balanced and detailed with an unprecedented calm reproduction. Many thanks to you and Rob.
Marcel –
One word: Brilliant! I had a Denafrips Pontus but it’s for sale now Not even close. This Spring Level 2 beats it on all aspects. Thanks Magna Hi!
Gerard (Verifizierter Besitzer) –
It is already (100-150 hours I estimate) by far the best DAC I have tried and my system is finally falling into place. In short, very happy with the Spring 3 with preamp and for me an end game piece,
Dave (Verifizierter Besitzer) –
Holoaudio spring dac 3 level 2
Tevredenheid hangt enerzijds af van de behandeling in de winkel en anderzijds van de kwaliteit van de producten. Om met het laatste te beginnen. Meer dan 40 jaar is mijn hobby hifi. Als ik iets koop wil ik iets goeds hebben waar ik lang van kan genieten. Voor sommige producten is dat eenvoudiger als andere. Zo kocht ik mijn eerste Magnepans in 1980, gevolgd door de 2.6 in 1998 en enige jaren geleden de 3.7. De 2.6 is nog steeds in gebruik in de 2e installatie.
Met dac’s is het een ander verhaal. De een na de ander. Toen ik 2 jaar geleden de NAD M51 verving door de RME ADI-2 fs dacht ik hier zeker met een goede externe voeding een eindpunt bereikt te hebben. De Denafrips Ares II bracht me echter op het spoor van r2r dac’s. De Ares is na 9 maanden in de 3e installatie in de slaapkamer beland omdat aan en uitzetten met een ifi i-usb 3.0 tussengeschakeld dagelijks een moeizame operatie was.
Mijn werkwijze is het afstruinen van het internet en beoordelen van reviews en reviewers. Ik kwam bij Holoaudio en Magna terecht en heb vrij snel een Holo spring dac 3 level 2 (ik heb mijn zilveren interlinks enige jaren geleden vervangen door professionele summer carbon interlinks met voor mijn oren een beter resultaat) en een singxer-SU2 gekocht. Wat een verschil met RME en Ares II, dag en nacht. Dit had ik echt niet verwacht. Eindelijk een dac die bijzonder goed een geluidsbeeld in de diepte kan neerzetten met een gedetailleerdheid en een rust die ik waar dan ook nog nooit heb gehoord.
De koopervaring: na het bestellen begint altijd het wachten. Binnen 2 dagen perfect geleverd. Had zelf een kleinigheidje. Ik had de Singxer op mijn mac moeten selecteren wat ik vergeten was. Binnen enige uren een reactie per mail terug. Kan niet beter. Zeer warm aanbevolen.
Stefan –
After contacting Rob, I drove to the listening studio. A nice and relaxing receive. Listened a lot to the different Holo DACs and finally opted for the Spring Level 2. Fantastic sonic characteristics that sounds lifelike. The preamp option suited me as I have active speakers. I am happy with the purchase and the pleasant experience at Magna Hifi!